The task of self-repairing a slow-draining bathtub’s feet is frequently not as challenging as many people imagine. The majority of clogged bathtub front difficulties may be fixed with a few simple, inexpensive, and uncomplicated equipment and techniques. Once the bathtub drain has been corrected, you should attempt to avoid or lower the likelihood that it will occur again; see my recommendations at the bottom of the page for ideas.
Six Solutions for Slow bathtub drain
- use vinegar with baking soda (the natural alternative to chemicals).
- Employ a plunger.
- Utilize a commercial clog remover (chemical).
- To see inside and get access, take off the drain stopper.
- Use a snake like a plumber.
- Phone a plumber.
Citric Acid with Baking Soda
This approach will remove modest obstructions and is more natural than utilizing cleaning agents.
Baking Soda and Vinegar Badkarsavlopp Unclogging Method
- Half a cup of baking soda should be poured down the drain hole.
- Add a cup of white vinegar after that.
- Five minutes should pass while the mixed components froth.
- Let the hot water run for about a minute.
- Check to see whether the bathtub drain is still sluggish.
Employ a plunger
Plunging is a procedure that is always worth trying because it takes little time and money. Plunging can work, but it relies on the type of obstruction, where it is located, and how your bathtub front is constructed. The plunger needs suction to operate, therefore it’s possible that this approach won’t work if the clog is severe and primarily formed of hair, for example.
How to use a plunger to unclog a clogged bathtub drain
- For a better seal, apply petroleum jelly to the plunger’s rim.
- Fill the bathtub feet with water until the plunger’s head is completely immersed.
- Pump briskly to plunge the bathtub drain hole.
Commercial Clog Remover (Chemical)
Strong chemical cleaners are widely accessible at hardware stores and supermarkets and are made to unclog the bathtub front. Pay close attention to the directions on the label or package.
How to use chemicals to unclog a dusch och badkarsblandare
The instructions on the box, including how much of the product to use, should be read and followed. The quantity you use will differ.
- To protect your hands and eyes, wear gloves and goggles.
- Avoid combining dissimilar chemicals as this might produce a gas that is harmful.
- Chemicals should be poured down the drain.
- To examine and get access, remove the drain stopper.
It’s time to get your hands dirty if you’ve tried the aforementioned strategies and none of them have succeeded. The overflow plate must be unscrewed and removed, followed by the stopper.
The drain is opened and closed by the stopper by raising and lowering a plunger. It’s controlled by a little lever. The stopper may be caught in a semi-closed position, preventing water flow if it is not functioning properly. The lock nuts that secure the plunger to the threaded rod allow for simple adjustment of the plunger’s position.
If the stopper functions properly, your issue is most likely a clog, and you will need to use a plumber’s snake to clear it. The overflow provides access.
Employ a plumber’s snake
This is another simple repair for a sluggish bathtub drain. If a blockage is a problem, there is a good chance of success.
How to Use a Plumbers’ Snake to Unclog Your Bathtub Drain
After removing the stopper, you may use the overflow to reach the drain (see above). After removing the strainer, another entrance is available through the drain aperture. Feed the snake until it reaches the obstruction.
- To raise the snake once again, turn the handle.
- To examine the drain and make sure the clog is gone entirely, run water down it.
- This method might need to be repeated numerous times.
Request a plumber
You must contact a licensed plumber if you don’t want to disassemble your drain and don’t feel comfortable using chemicals (or they don’t work). Obviously, if you’re trying to save money, this is your final option. Having said that, it is also the easiest.
What Leads to Slow Tub Draining?
A blockage that is preventing water from flowing freely is frequently to blame for bathtub feet that drain slowly. Usually, clogs are formed from soap, filth, grease, and/or tangled hair. Hair can round some portions of the drain, making them challenging to clean out. Homes with one or more occupants who have long hair tend to have clogs more frequently. Short hair is far less likely to clog the drains.
A Slow-Draining Tub’s Symptoms
When the water in the tub takes an excessively long time to drain after you remove the plug, it is said to be “slow draining.” In more severe situations, the water either stays for an extended period of time or takes longer than it should vanish. The issue might not be immediately apparent and might arise gradually over time. People frequently overlook problems until they become too serious to ignore.
Unfortunately, once a drainage issue starts, unless something is done about it, it typically simply becomes worse. This is due to the fact that clogs have a tendency to get larger and more securely fastened over time as they gather and accumulate more debris (such as hair, dirt, and soap). The sooner you address the issue, the simpler it will be to fix.
How to stop a bathtub’s feet from draining slowly
Of course, prevention is usually always preferable to treatment. Therefore, after your drainage issues are fixed, don’t forget to reduce the likelihood of your bathtub drain being clogged once more. Here are two ideas to give a go.
- First, if you don’t already have one, you should definitely consider investing in a high-quality drain guard. By doing this, you may stop tiny objects and detritus like hair and children’s toys from going down the drain.
- Second, a safe soap dish is frequently beneficial since soap causes clogs to develop by fusing little hair clumps into bigger ones. (People sliding can result in major incidents owing to soap dropping into the tub or onto the floor.